Carbon steel anchor bolt or DIN982 lock nut: match the component to the connection

Back to list
TECHNICAL NOTECOMPARISON

Key data

Product type
Carbon steel material designations
Grade designations
Finish
Stated standards

Abstract

The Galvanized Carbon Steel Anchor is a drop-in anchor for solid concrete, while the DIN982 Nylon insert lock nut is a threaded fastening component. Compare their shared material, grade, finish, standard, and size information before placing an order.

Carbon steel anchor bolt or DIN982 lock nut: match the component to the connection
Illustration for reference; see the product page for actual photos and specifications.
§1

Start with the connection type

A carbon steel anchor bolt choice depends first on how the connection is formed. The Galvanized Carbon Steel Anchor is a drop-in anchor for solid concrete. It is placed in a prepared hole, expanded with an installation tool, and completed with a hex bolt. Its drop-in design leaves nothing protruding above the surface after proper installation.

The DIN982 Nylon insert lock nut carbon steel zinc plated is a nylon insert lock nut. It belongs in a threaded fastening assembly where the nut must match the mating thread and the required specification. It is not a substitute for a concrete anchor.

§2

Side-by-side comparison

CriterionGalvanized Carbon Steel AnchorDIN982 Nylon insert lock nut carbon steel zinc plated
Product typeDrop-in anchorNylon insert lock nut
Carbon steel material designations1010, 1035, 1045Q195, 1035, 1045, 10b21
Grade designations4.8, 5.8, 6.8, 8.8, 10.9, 12.94, 6, 8, 10, 12
FinishPlain, zinc plated, black oxide, H.D.G.Zinc plated
Stated standardsISO, DIN, ANSI, JIS, BS, and non-standardGB, DIN, ISO, ANSI/ASTM, BS, BSW, JIS, and non-standard OEM
Size informationInch sizes from 1/4″ to 3/4″; metric sizes M6 to M20M5-M56; metric and imperial (inch) measurement

The shared material designations are 1035 and 1045. The anchor uses decimal grade designations, while the lock nut uses whole-number grade designations, so the two grade formats should remain separate in a purchase specification.

§3

Concrete installation versus threaded fastening

Choose the Galvanized Carbon Steel Anchor when the substrate is solid concrete. The installation sequence uses a straight-hole drill, hole cleaning, anchor placement, hammering the inner core with a rod, and tightening a hex bolt. Each size needs its corresponding installation tool. The stated environment is indoor dry concrete.

The anchor is intended for solid concrete and should not be used in brick or block. Check the required hole diameter and depth against the selected anchor size, then include the installation tool in the order plan.

Choose the DIN982 lock nut when the assembly already has a compatible threaded member. Its M5-M56 size range and metric or imperial measurement options make thread and size the first checks for this component. Match the nut's material designation, grade, and zinc-plated finish to the purchase specification.

§4

Material, grade, finish, and standard checks

The anchor lists carbon steel materials 1010, 1035, and 1045. The lock nut lists Q195, 1035, 1045, and 10b21. If you require a specific material designation, write that designation beside the selected component instead of treating all carbon steel entries as identical.

The anchor finish choices include plain, zinc plated, black oxide, and H.D.G. The DIN982 product is identified as zinc plated. Keep the finish requirement tied to the correct component when preparing a quotation or purchase order.

Both products include DIN, ISO, ANSI, and BS in their stated standard lists. The anchor also lists JIS, while the lock nut lists GB, ANSI/ASTM, BSW, and JIS. These standard references describe the product options, so the order should name the standard family required for each part.

The two options

Galvanized Carbon Steel AnchorDIN982 Nylon insert lock nut carbon steel zinc plated

Which component fits the order?

Select the Galvanized Carbon Steel Anchor for a drop-in anchoring point in solid concrete. Select the DIN982 Nylon insert lock nut carbon steel zinc plated for a threaded assembly that requires a nylon insert lock nut.

Before releasing the order, provide the anchor's substrate and hole requirements, or provide the lock nut's mating thread, size, material designation, grade, and finish. Those details identify the component that matches the connection.

The company

Yongnian Country Tianbang Fasteners Co., Ltd

Yongnian Country Tianbang Fasteners Co., Ltd was established in 2005, located in fasteners Industrial District Yongnian. We have more than 10 years production experience of fasteners. Our Products Yongnian Country Tianbang Fasteners Co., Ltd was established in 2005, located in fasteners Industrial District Yongnian. We have more than 10 years production experience of fasteners. Size M3-M52, length 10mm-6000mm. The annual production capacity is over 20,000 ton. Grade: 4.8, 6.8, 8.8, 10.9, 12.9.

About Us ↗Visit company website ↗

Post time: Nov . 17, 2026 01:31
Prev:

This is the first article

If you are interested in our products, you can choose to leave your information here, and we will be in touch with you shortly.